iRobot Vacuum Cleaner 74520 User Manual

®
Roomba  
Vacuum Cleaning Robot  
700 series  
Owner’s Manual  
 
Cleaning Modes and Pattern  
Virtual Wall® Optional accessory for all models.  
Virtual Walls create an invisible barrier that your Roomba won’t cross. That makes it easy  
to confine it to a particular room or area, and prevent it from getting too close to anything  
delicate or dangerous.  
Roomba uses iAdaptResponsive Cleaning Technology, an advanced, proprietary  
system of software and sensors. iAdapt allows Roomba to actively monitor the cleaning  
environment more than 60 times per second and respond with over 40 different mobility  
behaviors to clean the room more thoroughly.  
• Each Virtual Wall needs two C alkaline  
Roomba 700 Series has 3 cleaning modes you can select:  
batteries (not included).  
Clean Mode – Roomba automatically calculates the room size and adjusts its cleaning  
time appropriately.  
You can set the Virtual Walls to block an  
opening of up to 7 feet (2 meters).  
It creates a cone shape barrier, so the  
beam gradually gets wider.  
Spot Mode – Roomba will spiral approximately 3 feet (1 meter) in diameter  
and then spiral back to where it started – an intense, localized clean for those  
quick fixes.  
• For best results, place the Virtual Wall  
on the outside of the doorway you  
want to block. Point the arrows on the  
top towards the opening.  
Scheduled Cleaning Mode – Roomba leaves its Home Base, cleans, and then  
returns to recharge when its done.  
Manual Virtual Wall  
Surfaces  
Turn on a Manual Virtual Wall by hand at the beginning of the cleaning cycle.  
It will shut off after 135 minutes. If the power light blinks green, it means you’ll  
need new batteries soon.  
Your Roomba works on pretty much anything – wood, carpet, tile, vinyl and linoleum,  
adjusting to different floor types. It automatically senses stairs and other drops.  
It might stall when confronting round edges and might slide over particularly slippery  
surfaces. Very dark floors may impede its sensors. Roomba is not designed for  
use outdoors.  
Auto Virtual Wall  
• When an Auto Virtual Wall is set to “AUTO” mode, the power light continuously blinks  
to indicate it is on. When battery levels are low, the Virtual Wall continuously blinks  
twice to indicate that it needs new batteries. When in AUTO mode, the batteries  
should last for around six months. To save on batteries, just switch it to OFF.  
Anti-tangle system  
Roomba won’t get caught up in tassels or fringes. If it senses a tangle, it  
automatically stops its brushes and spins them in reverse to free itself.  
Virtual Wall Lighthouse™ Accessory for models 780 and above only.  
Home Base  
Position the Home Base on a hard, level surface against a wall. Make sure its at least  
4 feet (1.5 meters) from any stairs and that your Roomba has a clear path to reach it.  
A Virtual Wall Lighthouse can act as both a Virtual Wall and a Lighthouse.  
In Lighthouse mode, it helps your Roomba navigate around your home.  
In Virtual Wall mode, it blocks off areas you don’t want cleaned.  
When Roomba has finished cleaning, it will return to its Home Base to charge.  
The light on the Home Base stops blinking and turns solid green when Roomba  
makes a good connection. Then, Roombas battery indicator will pulse amber to  
show it is charging, and will turn solid green when Roomba is fully charged and  
ready to clean again!  
Simply use the Mode Selector to make your choice. Either way, it turns on and off  
automatically as you turn your Roomba on and off. When on, the light on top is lit.  
Each Virtual Wall Lighthouse needs two C alkaline batteries (not included). A flashing  
power light means the batteries need replacing soon.  
Getting started | Cleaning modes & Virtual Walls  
3
4
 
Battery storage and charging  
Your Roomba is powered by a rechargeable battery. Before using your Roomba  
for the first time, you’ll need to charge the battery overnight.  
• Make sure your Roomba is fully charged before each cleaning cycle.  
For maximum battery life, always store your Roomba plugged in.  
• When your Roomba is on the Home Base, make sure the Home Base  
power light is on.  
• If you return your Roomba to the Home Base / battery charger after leaving  
it off for a long time, it will start a special Refresh Charge mode and the battery  
indicator will pulse quickly. If possible, don’t interrupt the Refresh Charge mode.  
• For long-term storage, fully charge the battery, remove, and store it in a  
cool, dry place.  
How to use the Lighthouse mode  
Simply place a Lighthouse in the doorway  
with the logo facing forward. When it has  
completed the first room the Lighthouse  
will help Roomba navigate around your  
home allowing it to clean room-to-room.  
When Roomba has completed cleaning,  
the Lighthouse will direct Roomba back  
to its Home Base for recharging.  
How to remove your battery  
If you won’t be using your Roomba for an extended period, we recommend that you  
remove the battery. To access the battery, turn Roomba over and remove the two  
screws that hold Roombas battery cover in place.  
You can use Lighthouses and Virtual Walls  
at the same time, but avoid placing them  
too close to each other, to the Home Base, or to furniture that could block the invisible  
beams. Otherwise your Roomba might not recognize the Lighthouses or be able to  
return to Home Base.  
User Interface Icons  
Icon  
What does it mean?  
The Anti-tangle Indicator turns on while Roomba is freeing  
itself from a tangle.  
The Dirt Detect Indicator flashes when dirt is detected and  
persistent pass cleaning pattern is initiated.  
How to use the Virtual Wall mode  
In Virtual Wall mode, the Lighthouse creates an invisible barrier that your Roomba won’t  
cross. It automatically turns off when your Roomba is turned off.  
The Troubleshooting Light blinks when there is an issue  
(see pages 11 and 12).  
Simply place the Virtual Wall Lighthouse in the center of the doorframe. Unlike a Virtual  
Wall, a Virtual Wall Lighthouse features a range selector that you can use to adjust the  
length of the barrier – up to 8 feet (2 meters) – (a longer range will drain the  
battery faster).  
The Full Bin Indicator (models 770 and above) lets you know  
when the dust bin is full and needs to be emptied.  
The Battery Indicator shows the battery status.  
Solid red --- Battery drained  
Amber pulse --- Charging  
Solid green --- Fully charged  
Quick amber pulse --- Refresh Charge mode  
Battery storage & charging | Charging lights  
5
6
 
Viewing a schedule  
1. Turn ON your Roomba by pressing CLEAN.  
2. Press SCHEDULE.  
Remote Control  
You use this just like your TV remote, pointing and clicking it to turn your Roomba on  
and off, steer it, and control the SPOT and DOCK (...) functions.  
3. Press DAY to look through the scheduled cleaning times.  
4. Press OK to save changes. To exit or cancel press CLEAN.  
• First, install 2 AA batteries (not included).  
• If you use it near a Virtual Wall or the Home  
Directional  
Buttons  
Deleting a schedule  
1. Turn ON your Roomba by pressing CLEAN.  
2. Press SCHEDULE.  
Base, it may get confused and not work.  
SPOT  
Button  
...Button  
CLEAN/power  
Button  
3. Press DAY to look through the scheduled cleaning times.  
4. When your Roomba is displaying the scheduled cleaning time you want to delete,  
press HOUR until --:-- is displayed. Press OK to save changes.  
5. To delete all schedules, press DAY for 5 seconds.  
Wireless Command Center  
Optional accessory for models 780 and above.  
Use this to turn your Roomba on and off, schedule up to seven cleaning times a week  
and steer it.  
Changing a schedule  
1. Turn ON your Roomba by pressing CLEAN.  
2. Press SCHEDULE.  
Scheduling your Roomba  
3. Press DAY to look through the scheduled cleaning times.  
4. When your Roomba is displaying the scheduled cleaning time you want to change,  
press HOUR and MINUTE individually to make the change.  
5. Press OK to save changes. To exit or cancel press CLEAN.  
This lets you tell your Roomba exactly when to clean, even when you’re away  
from home. You can schedule Roomba to clean once per day, up to seven times  
per week.  
Setting the time  
1. Turn ON your Roomba by pressing CLEAN.  
2. Press CLOCK.  
3. Use DAY, HOUR and MINUTE individually to set the correct time.  
4. Press OK to save changes. To exit or cancel press CLEAN and start again.  
A little maintenance goes a long way  
To keep your Roomba working perfectly, its a good idea to do a little  
maintenance regularly. In particular, please note the following:  
Setting 12 / 24 hr  
To switch between the two views, press and hold CLOCK until the display shows  
12h or 24h. Then press CLOCK to switch and press OK to save changes.  
• Look for the yellow parts – these are designed to be removed  
and cleaned.  
You should empty the bin and clean the brushes after each use, if possible.  
• Excessive hair build-up could permanently damage your Roomba or your floor,  
so clean the brush bearings and brush caps regularly.  
Roombas clock will switch back to the default 12 hour (AM/PM) format when  
Roombas battery is disconnected or significantly discharged.  
Setting a schedule  
You can schedule your Roomba to clean once a day, up to seven times a week.  
You must set the internal clock before setting a schedule.  
1. Turn ON your Roomba by pressing CLEAN.  
2. Press SCHEDULE.  
3. Use DAY, HOUR and MINUTE individually to set the schedule.  
4. Press OK to save changes. To exit or cancel press CLEAN and start again.  
Controlling and Scheduling your Roomba | Regular maintenance  
7
8
 
Essential maintenance  
4. To clean the side brush, use a small  
Phillips screwdriver to remove the screw  
from the center. Remove the brush,  
clean, reinstall.  
Emptying the bin  
You should do this after each use.  
Ensure proper insertion of the bin each  
time as Roomba will not run without it.  
Cleaning the front wheel  
1. Pull firmly on the front wheel to remove it.  
2. Remove any debris from inside the  
wheel cavity.  
3. Remove the wheel from its housing and  
wipe clean. Pull firmly to remove the axle  
and clear any hair wrapped around it.  
4. Reinstall all parts when finished. Make  
sure the wheel clicks right back into place.  
Cleaning the two filters  
Regular cleaning is important and  
you should replace the filters after two  
months of regular use.  
Cleaning the bin sensors  
Cleaning the brushes and  
associated parts  
(models 770 and above only)  
Remove the bin and wipe the two optical  
bin sensors with a clean, dry cloth.  
1. Remove brush guard by lifting both  
yellow tabs.  
Bin sensors  
Bearings  
Cleaning the cliff sensors  
Simply wipe all six cliff sensor openings  
with a clean, dry cloth.  
Cliff sensor openings  
2. Remove and clean the two brushes  
and brush bearings.  
Troubleshooting  
Occasionally, something can go wrong. But  
don’t worry – theres an early warning system.  
3. Use the included cleaning tool to  
remove hair easily from the bristle  
brush by pulling it over the brush.  
Your Roomba will tell you what the problem  
is. The troubleshooting light will also blink.  
To repeat an error message, just press CLEAN.  
For more information you can download a detailed user manual at www.irobot.com  
Essential Maintenance | Step by step  
9
10  
 
Problems while cleaning  
Problems while charging  
Your Roomba  
blinks and says…  
Likely cause  
What to do  
Your Roomba  
blinks...  
Your Roomba  
displays...  
Your Roomba  
says...  
Likely  
cause...  
What to do  
Error 1. Move Roomba  
to a new location then  
press CLEAN to restart.  
Your Roomba is stuck  
with a wheel hanging  
down.  
Ensure your Roombas  
wheels are firmly on the floor.  
Start in a new location.  
1 blink  
-
Charging error 1  
Your Roombas  
battery Isn’t  
connected.  
Check that you  
removed pull-tab  
from the battery.  
Remove the bat-  
tery cover of your  
Roomba to remove  
& reinstall battery.  
Error 2. Open Roombas  
brush cage and clean  
brushes.  
Your Roombas main  
brushes can’t turn.  
Remove and clean your  
Roombas brushes.  
Let your Roomba  
cool down for at  
least an hour & try  
charging again.  
Your Roomba  
has a charging  
error.  
2 blinks  
Err 2  
Charging error 2  
Error 5. Spin Roombas  
side wheels to clean.  
Your Roombas side  
wheel is stuck.  
Clean your Roombas side  
wheels. Push them in and  
out and check that they  
both turn freely. Start in a  
new location.  
Reset Roombas  
software (pg13) and  
try charging again.  
Your Roomba  
has a charging  
error.  
3 blinks  
5 blinks  
Err 3  
Err 5  
Charging error 3  
Charging error 5  
Error 6. Move Roomba  
to a new location then  
press CLEAN to restart.  
Your Roombas cliff  
sensors are dirty or  
your Roomba is  
Wipe your Roombas cliff  
sensors with a dry cloth.  
Start in a new location.  
Your Roomba  
has a charging  
error.  
Reset Roombas  
software (pg13) and  
try charging again.  
hanging over a drop.  
Error 7. Spin Roombas  
side wheels to clean.  
Your Roombas side  
wheel is stuck.  
Clean your Roombas side  
wheels of hair and debris. Push  
them in and out and check that  
they both turn freely.  
Your Roomba  
has a charging  
error.  
Let your Roomba  
cool down for at  
least an hour & try  
charging again.  
6 blinks  
7 blinks  
Err 6  
Err 7  
Charging error 6  
Charging error 7  
Start in a new location.  
Error 9. Tap Roombas  
bumper to clean.  
Your Roombas bumper  
is compressed or the  
bumper sensor is dirty.  
Briskly tap your Roombas  
bumper several times to  
dislodge any debris that  
may be trapped underneath.  
Your Roombas  
battery Isn’t  
cooling.  
Let your Roomba  
cool down for at  
least an hour & try  
charging again.  
Error 10. Spin Roombas  
side wheels to clean.  
Your Roombas side  
wheel is stuck or its  
bumper isn’t detecting  
obstacles.  
If your Roomba is circling in  
one place, clean side wheels.  
Push them in and out and  
check that they both turn. If  
its not circling in one place,  
Roomba may be in a very large  
room. Use a Virtual Wall to  
create a smaller cleaning area.  
Language selection mode  
Your Roomba can provide troubleshooting messages in English, French, German,  
Spanish, Italian, Dutch, Danish, Swedish, Norwegian, Finnish, Polish, Russian,  
Portuguese, Japanese, Korean and Chinese.  
Setting the language  
The default language is English. To change this:  
1. Turn ON your Roomba by pressing CLEAN.  
2. Press and hold DOCK until it beeps and says the current language.  
3. Release DOCK.  
4. Now press CLEAN repeatedly until you hear the language you want.  
5. Press and hold CLEAN to turn off your Roomba and confirm language choice.  
Please charge  
Roomba.  
Your Roombas battery  
is dead.  
Plug your Roomba into the  
charger or place it on the  
Home Base to charge.  
Problem solving | When running or charging  
11  
12  
 
• Always remove the battery before long-term storage or transportation.  
• This appliance is not intended for use by persons (including children) with reduced physical, sensory  
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision  
or instruction concerning use of the appliance by a person responsible for their safety.  
• Children should be supervised to ensure they do not play with the appliance.  
How to reset the software  
Hold down CLEAN for ten seconds. This will clear the clock  
and may disrupt successful docking for the first few charge cycles.  
Roomba battery pack and charging  
Frequently asked questions  
• Charge using a standard outlet only. Product may not be used with any type of power  
converter. Use of other power converters will immediately void the warranty.  
• Use only the battery charger supplied by the manufacturer to charge this device.  
• Do not use a battery charger with a damaged cord or plug.  
• Charge indoors only.  
• Roombas battery charger may be protected with a surge protector in the event of severe  
electrical storms.  
• Never handle the battery charger with wet hands.  
Why does my Roomba’s side brush occasionally spin backwards?  
When caught on items such as carpet tassels or wires, the side brush may spin slowly or even  
backwards to free itself. This may also occur on thick carpets. If it does this at other times, you  
should clean the brush.  
Why does my Roomba occasionally make a thumping sound?  
When Roombas brushes encounter items such as carpet tassels or wires, the brushes will  
briefly reverse direction to get free. This makes a thumping sound. If you hear a thumping  
sound at any other time, you should clean the main brushes.  
• Always disconnect Roomba from the battery charger before cleaning.  
• Please ensure voltage rating for enclosed battery charger matches standard outlet voltage.  
Why doesn’t my Roomba slow down as it approaches certain obstacles?  
Your Roomba usually identifies obstacles quickly, allowing it to slow down and gently touch the  
obstacle with its bumper before changing direction. However, it may be less effective at sensing  
extremely dark surfaces, or objects under 2 inches (5 centimeters) wide.  
What if I need further help or accessories?  
iRobot Customer Care USA  
If you have questions or comments about Roomba, please contact iRobot before contacting  
questions,or information about accessories and other iRobot products. We would like  
Important safety instructions  
CAUTION: DO NOT EXPOSE THE ELECTRONICS OF ROOMBA, ITS BATTERY, OR THE BATTERY  
CHARGER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL. PLEASE ENSURE VOLTAGE RATING FOR ENCLOSED BATTERY CHARGER  
MATCHES STANDARD OUTLET VOLTAGE. Always exercise caution when operating your Roomba. To  
reduce the risk of injury or damage, keep these safety precautions in mind when setting up, using and  
maintaining Roomba:  
to hear from you.  
Should you still need assistance:  
• Call our customer care representatives at 877.855.8593  
iRobot Customer Care Hours:  
• Monday – Friday 9AM – 7PM Eastern Time  
• Saturday 9AM – 6PM Eastern Time  
General  
• Read all safety and operating instructions before operating Roomba.  
• Retain the safety and operating instructions for future reference.  
• Heed all warnings on Roomba, Battery, AC Adapter and in Owners Manual.  
• Follow all operating and use instructions.  
iRobot Customer Care International  
To contact an international partner near you for sales and technical support,  
• Refer all non-routine servicing to iRobot.  
Roomba use  
• Roomba is for indoor use only.  
• Roomba is not a toy. Do not sit or stand on this device. Small children and pets should be supervised  
when Roomba is cleaning.  
• Clean with a dry cloth only. Do not pour or spray liquids onto Roomba.  
• Do not use this device to pick up anything that is burning or smoking.  
• Do not use this device to pick up spills of bleach, paint, or other chemicals, or anything wet.  
• Before using this device, pick up objects like clothing, loose papers, pull cords for blinds or curtains,  
power cords, and any fragile objects. If the device passes over a power cord and drags it,  
there is a chance an object could tumble off a table or shelf.  
• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent  
access to the balcony and ensure safe operation.  
Problem solving | Further help  
13  
14  
 
Declaration of conformity  
iRobot Roomba ® Vacuum Cleaning Robot and Accessories  
Manufacturer: iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730, USA  
Declares that Roomba along with Model 17062 and 17063 Battery Chargers and the Home Base, conform to the requirements of:  
Low Voltage Directive 73/23/EEC as amended by 93/68/EEC and EMC Directive 89/336/EEC as amended by 92/31/EEC.  
It is further declared that the Roomba and Roomba SE Robotic Vacuum Cleaner and Accessories conform to the following harmonised  
European standards:  
Year of CE Marking: 2004  
EN 60335-1:2002 + A11:2004  
Household and Similar Electrical Appliances - Safety Part 1 - General Requirements  
EN 60335-2-2:2003  
Household and Similar Electrical Appliances - Safety Part 2 - Particular Requirements for Vacuum Cleaners and Water-Suction Cleaning  
Appliances  
EN 60335-2-29:2002  
Household and Similar Electrical Appliances - Part 2-29 - Particular Requirements for  
Battery Chargers  
EN 55014-1:2000 + A1:2001 + A2:2002  
Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus -- Part 1: Emission  
EN 55014-1:1997 + A2:2002  
Electromagnetic compatibility - Requirements for household appliances, electric tools  
and similar apparatus -- Part 2: Immunity - Product family standard  
Low Voltage tests and EMC tests have been conducted by:  
TUV Rheinland of North America  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with  
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely  
to cause harmful interference in which case the user will be required to correct the interference at his own expense.  
© 2010-2011 iRobot Corporation, 8 Crosby Drive, Bedford, MA 01730. All rights reserved.  
iRobot, Roomba and Virtual Wall are registered trademarks of iRobot Corporation. Dirt Detect, Home Base and Lighthouse are  
trademarks of iRobot Corporation. [00256.1210.v1]  
U.S. Pat. Nos. D556,961 | 6,594,844 | 6,690,134 | 6,809,490 | 6,883,201 |6,956,348 | 7,155,308 | 7,173,391 | 7,196,487 | 7,288,912 |  
7,288,912 | 7,332,890 | 7,388,343 | 7,389,156 | 7,429,843 | 7,430,455 | 7,441,298 | 7,448,113. Additional patents pending.  
15  
16  
 

Insignia Portable DVD Player NS PDVD10 User Manual
Ironman Fitness Home Gym Achiever User Manual
Jensen Digital Camera KT7015A User Manual
Johnson Controls Film Camera R 22 S1 1TVM2 User Manual
JVC Camcorder GR D239 User Manual
JVC Camcorder LYT2184 001A M User Manual
JVC Car Stereo System GET0163 001A User Manual
JVC DVD Player UXQD90S User Manual
Keys Fitness Fitness Equipment KPS CC User Manual
KitchenAid Refrigerator KBLS20EVMS00 User Manual